Cisco3550恢复出厂设置方法-Cisco教程-爱易网页

Cisco3550恢复出厂设置方法

日期：2015-08-04　浏览次数：4402 次

Cisco 3560交换机在配置为三层交换机后恢复出厂设置方法：

qls207# en （*****进入特权模式*****）

qls207#write erase （*****清除配置*****）

Erasing the nvram filesystem will remove all configuration files! Continue? [confirm]回车

[OK]

Erase of nvram: complete

qls207#

*Mar 1 00:02:20.618: %SYS-7-NV_BLOCK_INIT: Initialized the geometry of nvram

qls207#

qls207#reload

Proceed with reload? [confirm]回车

*Mar 1 00:03:04.272: %SYS-5-RELOAD: Reload requested by console. Reload reason:

Reload command

Using driver version 1 for media type 1

Base ethernet MAC Address: 08:17:35:7d:96:00

Xmodem file system is available.

The password-recovery mechanism is enabled.

Initializing Flash...

mifs[2]: 0 files, 1 directories

mifs[2]: Total bytes : 3870720

mifs[2]: Bytes used : 1024

mifs[2]: Bytes available : 3869696

mifs[2]: mifs fsck took 0 seconds.

mifs[3]: 388 files, 7 directories

mifs[3]: Total bytes : 27998208

mifs[3]: Bytes used : 12858368

mifs[3]: Bytes available : 15139840

mifs[3]: mifs fsck took 6 seconds.

...done Initializing Flash.

done.

Loading "flash:/c3560-ipbasek9-mz.122-50.SE1/c3560-ipbasek9-mz.122-50.SE1.bin"..

.@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@

@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@

@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@

File "flash:/c3560-ipbasek9-mz.122-50.SE1/c3560-ipbasek9-mz.122-50.SE1.bin" unco

mpressed and installed, entry point: 0x3000

executing...

Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

Rights clause at FAR sec. 52.227-19 and subparagraph

Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.

170 West Tasman Drive

San Jose, California 95134-1706

Cisco IOS Software, C3560 Software (C3560-IPBASEK9-M), Version 12.2(50)SE1, RELE

ASE SOFTWARE (fc2)

Compiled Mon 06-Apr-09 08:00 by amvarma

Image text-base: 0x00003000, data-base: 0x01900000

Initializing flashfs...

Using driver version 1 for media type 1

mifs[3]: 0 files, 1 directories

mifs[3]: Total bytes : 3870720

mifs[3]: Bytes used : 1024

mifs[3]: Bytes available : 3869696

mifs[3]: mifs fsck took 0 seconds.

mifs[3]: Initialization complete.

mifs[4]: 388 files, 7 directories

mifs[4]: Total bytes : 27998208

mifs[4]: Bytes used : 12858368

mifs[4]: Bytes available : 15139840

mifs[4]: mifs fsck took 1 seconds.

mifs[4]: Initialization complete.

...done Initializing flashfs.

Checking for Bootloader upgrade.. not needed

POST: CPU MIC register Tests : Begin

POST: CPU MIC register Tests : End, Status Passed

POST: PortASIC Memory Tests : Begin

POST: PortASIC Memory Tests : End, Status Passed

POST: CPU MIC interface Loopback Tests : Begin

POST: CPU MIC interface Loopback Tests : End, Status Passed

POST: PortASIC RingLoopback Tests : Begin

POST: PortASIC RingLoopback Tests : End, Status Passed

POST: PortASIC CAM Subsystem Tests : Begin

POST: PortASIC CAM Subsystem Tests : End, Status Passed

POST: PortASIC Port Loopback Tests : Begin

POST: PortASIC Port Loopback Tests : End, Status Passed

Waiting for Port download...Complete

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

export@cisco.com.

cisco WS-C3560V2-24TS (PowerPC405) processor (revision F0) with 122880K/8184K by

tes of memory.

Processor board ID FDO1446V11K

Last reset from power-on

1 Virtual Ethernet interface

24 FastEthernet interfaces

2 Gigabit Ethernet interfaces

The password-recovery mechanism is enabled.

512K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address : 08:17:35:7D:96:00

Motherboard assembly number : 73-11765-08

Power supply part number : 341-0328-02

Motherboard serial number : FDO14461EHU

Power supply serial number : DCA1445M0SR

Model revision number : F0

Motherboard revision number : A0

Model number : WS-C3560V2-24TS-S

System serial number : FDO1446V11K

Top Assembly Part Number : 800-31050-04

Top Assembly Revision Number : B0

Version ID : V04

CLEI Code Number : COMP900ARA

Hardware Board Revision Number : 0x03

Switch Ports Model SW Version SW Image

------ ----- ----- ---------- ----------

* 1 26 WS-C3560V2-24TS 12.2(50)SE1 C3560-IPBASEK9-M

Press RETURN to get started!

*Mar 1 00:00:37.664: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, cha

nged state to down

*Mar 1 00:00:38.956: %SPANTREE-5-EXTENDED_SYSID: Extended SysId enabled for typ

e vlan

*Mar 1 00:01:00.574: %SYS-5-RESTART: System restarted --

Cisco IOS Software, C3560 Software (C3560-IPBASEK9-M), Version 12.2(50)SE1, RELE

ASE SOFTWARE (fc2)

Compiled Mon 06-Apr-09 08:00 by amvarma

--- System Configuration Dialog ---

Enable secret warning

----------------------------------

In order to access the device manager, an enable secret is required

If you enter the initial configuration dialog, you will be prompted for the enab

le secret

If you choose not to enter the intial configuration dialog, or if you exit setup

without setting the enable secret,

please set an enable secret using the following CLI in configuration mode-

enable secret 0 <cleartext password>

----------------------------------

Would you like to enter the initial configuration dialog? [yes/no]:

% Please answer 'yes' or 'no'.

Would you like to enter the initial configuration dialog? [yes/no]: n

Switch>

Switch>en

Switch#show run

Building configuration...

Current configuration : 1305 bytes

version 12.2

no service pad

service timestamps debug datetime msec

service timestamps log datetime msec

no service password-encryption

hostname Switch

boot-start-marker

boot-end-marker

no aaa new-model

system mtu routing 1500

ip subnet-zero

spanning-tree mode pvst

spanning-tree etherchannel guard misconfig

spanning-tree extend system-id

vlan internal allocation policy ascending

interface FastEthernet0/1

interface FastEthernet0/2

interface FastEthernet0/3

interface FastEthernet0/4

interface FastEthernet0/5

interface FastEthernet0/6

interface FastEthernet0/7

interface FastEthernet0/8

interface FastEthernet0/9

interface FastEthernet0/10

interface FastEthernet0/11

interface FastEthernet0/12

interface FastEthernet0/13

interface FastEthernet0/14

interface FastEthernet0/15

interface FastEthernet0/16

interface FastEthernet0/17

interface FastEthernet0/18

interface FastEthernet0/19

interface FastEthernet0/20

interface FastEthernet0/21

interface FastEthernet0/22

interface FastEthernet0/23

interface FastEthernet0/24

interface GigabitEthernet0/1

interface GigabitEthernet0/2

interface Vlan1

no ip address

ip classless

ip http server

ip http secure-server

control-plane

line con 0

line vty 5 15

end

Switch#

免责声明： 本文仅代表作者个人观点，与爱易网无关。其原创性以及文中陈述文字和内容未经本站证实，对本文以及其中全部或者部分内容、文字的真实性、完整性、及时性本站不作任何保证或承诺，请读者仅作参考，并请自行核实相关内容。

Cisco3550恢复出厂设置方法

相关资料更多>

推荐阅读更多>